Cannot Ping The Switches From Other Subnet

Di: Stella

Each VM is configured with an external switch in Hyper-V Manager. ABBOTT shows „No Internet“ in the taskbar, however it can ping Google.com, ping its Host, and shows I can’t ping/traceroute Remote devices via Diagnostics / Terminal of Sophos : or Local device present in the DHCP range of the Synology router : The ping process works from

Cannot Ping switch from local hosts Packet Tracer - Cisco Community

BUT I cannot ping the computers directly, i.e. 192.168.2.11 cannot ping 192.168.1.104, and vice versa. One of the computers is a Windows 10 machine, the other a Hi there, I have a very strange problem here. I have a few VLANs and communication between all of them is fine. My computers are on VLAN 100 and none of them IP Configuration: VMs need to be properly configured with IP addresses, subnet masks, and default gateways to communicate effectively. Common Causes for Ping Issues

Start a conversation Cisco Community Technology and Support Networking Switching Cannot ping IP on different subnet Bookmark | Subscribe Hello Spice heads, I’ve created a small lab at home. This lab consists of two distribution switches and two access switches. I have the 10.1.3.0 subnet as the management

Router and Switch cannot ping each other

how to process if FortiSwitches are unable to ping each other on the same VLAN when the VLAN is allowed between the switches.ScopeFortiSwitch v6.4.x / v 7.0.x /

Cisco Learning NetworkLoading × Sorry to interrupt CSS Error Refresh I have two VMs on this network, one has the IP of 10.72.1.17 and the other is 10.72.1.15. From both windows VMs I am able to ping the gateway at 10.72.1.1, however they cannot ping each Why I cannot ping other computer in the same subnet like for example: I cannot ping 192.168.88.153 but my ip is 192.168.88.140.

I’m trying to isolate some ports so they’re on a completely separate network from my office LAN. I want to use it for backups and maintenance. I currently do this with a small 8-port unmanaged I’ve factory reset the switch 3 times now, and just done this exact configuration, and cannot Error Refresh I have two ping the SVI. I know it can’t get out, or route anywhere but at a minimum I should be able to ping the Hello Shaunak, The interconnection from the router to the switch is done from the router F0 and connected to the switch f0/24. And the natting from inside is done by vlan1. 1.

Unable to ping between IPV6 addresses within the same LAN
How to ping a PC on a different subnet using Cisco Packet Tracer
Same VLAN and Subnet, Cannot Ping

I can ping every switch, on every VLAN, in any combination– the swtiches all see each other fine, and devices attached to ParkingLotSwitch or ServerSwitch get DHCP But as I connect 2 PC’s to it they cannot ping each other. They have both static set IP’s ( 192.168.2.181/24 and 192.168.2.69/24 ) on the same subnet. The same is true for

Would Ping from PC1 to PC2 work? No other L3 ports on these 2 devices and its forwarding table does not contain any entry apart from the one created due to configured I have two HP Switches on the same subnet 192.168.20.x/24. When connected via VPN I am able to ping and log in to one switch however I am unable to ping or log in to the all other ports are untagged vlan 30 all devices on the 1930 have power and are working but cannot get out past the 1930. Plugged laptop into a port and put a vlan 30 ip on it and cannot

Dns not being used to resolve hostname on another subnet.

Hi, I have a „ISR 2911“ with „EHWIC-4ESG“ used as ethernet switch module.. The four ports in this card are assigned to the same VLAN connecting to routers as these are in the Good morning, Trying to ping hosts on the same vlan (vlan 10) across a pair of 2950s. Oddly, each host cannot even ping its own switch or vice versa. Here are the shows:

Hi guys, Currently have the following network set up (see attachment pls). Apparently I’m supposed to be able to connect to each switch using all 3 PC’s. At the moment, Is there a setting on Windows10 that would permit a host to reply to pings only on the local subnet, but not but not if the request is from a machine on another subnet? I am I cannot ping between the two. I can even do a sh cdp neighbor detail on both devices and it will show the other device and IP address. Why can’t I ping? Default gateway set on switch to

The two affected Servers can both ping the internal network’s Gateway (172.16.2.1), and they can both ping other Servers on the same 172 Subnet without any issue. You may need a different vlan to check other switches and/or routers to verify that these routes are being properly redistributed via RIP. If that route is there, next verify that there is a route

I am trying to change the VLAN tag on a vlan on one of my core switches. Currently the network is vlan 5 and i need to change it to vlan 7. The subnet with remain the Switch is layer 3 core router – on the devices in each vlan use the switch as their default gateway Firewall is connected to the switch in a different vlan using the 10.10.5.0/24 subnet Did you add static routes to the firewall for all

Solved: layer 3 switch and ping problems

I cannot ping every 10.16.8 address across the various switches VLAN 2. I have tried an extended ping from the first switch EX. ping 10.16.8.55 source 10.16.8.1..

Cannot ping VLAN on other side of network, neither from switch to router Hello! I have this strange problem where I cannot ping from PC to outside of VLAN, neither from switch to router. Start a conversation Cisco Community Technology and Support Networking Switching other subnets unable to ping to certain IP Bookmark | Subscribe

I’ve got a bit of a head-scratcher here with a PC in a VLAN. It’s quite an odd one – this PC can ping other devices, be it other PCs or servers, within the same subnet or VLAN. However,

This should be an easy one for everyone. I have always worked with Cisco switches and I am having a difficult time setting up an HP Aruba Switch. I have two main

I have 3 endpoints connected to a virtual external switch. All endpoints can get out to the internet just fine, however I would like them to also be able to communicate locally as one of them is a All vlans can communicate with each other and the switches and router, vice versa etc. I can ping externally to another router on another network form this layer 3 switch

JQDN

General